Wanhao D9 – Bed leveling -do this to make it work!

Add M420 S1 after G28

 

Someone on facebook suggested that the stock wanhao Firmware doesn’t handle leveling propertly. They’re right

Check out……..

https://reprap.org/forum/read.php?415,789128

 

given the 1000’s of people having issues getting the D9 to print properly, there does seem to be something fundamentally wrong with the printer….

 

In your Cura / startup script, find G28

Continue reading “Wanhao D9 – Bed leveling -do this to make it work!”

Wanhao Duplicator 9 – New X Axis parts coming

It’s been a busy personal and work life for the past few weeks so it’s been difficult to ‘tinker’……….I have however made something new!………….. Continue reading “Wanhao Duplicator 9 – New X Axis parts coming”

Wanhao D9 Bed upgrade

The Wanhao Y axis ‘bed’ is known to be a little flimsy,

It’s made from pressed, welded steel sheet just under 1mm thick and notably flexes when adjusting the levelling springs

Some closeups below….

My new plan – Create a new Bed / Carriage with some suitably cut Aluminium from this bloke on ebay – 4mm thick and 325 x 325mm for just over £13, bargain!.

Once cut, this should be stiffer and more importantly, lighter than the existing carriage as shown below…….

 

https://www.ebay.co.uk/itm/Aluminium-Sheet-1mm-1-2mm-1-5mm-2mm-3mm-4mm-1050H14-S1BH4-Various-Sizes/271210657802

1 bed

2bed
When tightning, this black part can often bend, it’s only 1mm thick!
img_1175
Exposed bed – it looks ‘deep’ from the front, but the ‘wings’ on the sides are flimsy and flex with levelling

It’s alive! – kind of. MGN12 Rails update

Well, the MGN12H linear rail carriages fit into the new carriage adaptors I quickly knocked up in Tinkercad perfectly!

And, don’t they look lovely in Purple (great filament from 3D Filaprint)

Now, to dismantle the printer and see if the print bed tray fits…………

That’s the problem with printing stuff to upgrade a printer, iterating takes time and stuff gets dismantled waaay too much! I need a second printer :-p

D9 Printer Bed Levelling – Done Right

 

bed-leveling-on-Ultimaker2-1.jpgFinally – Wanhao have released a decent firmware – V0.164(B)

Now, Levelling the bed…..

 

There’s LOADS of videos, methods ,etc out there….this way is SIMPLE, CONSISTENT and reliable

Make sure your printer head is clean and free from cooled plastic

MAKE SURE THE BED IS CLEAN...(I’m using baby wet wipes, but they dont’ seem to be the best, i’ll need to try isopropyl alcohol like the old timers are)

How to clean….Use a sponge, soap and water………that’s it!

1 – LEVEL the Z axis – use a ruler / visual marks on the back, whatever, make sure the bar is level

2 – Use the menu to go into  the LEVEL selection

3 – Get the Z axis offset correct by using a piece of paper so it’s just gripped by the head

4 – TURN OFF THE PRINTER (yes, TURN IT OFF, DO NOT CLICK NEXT)

5 – MANUALLY move the print head to CLOSE (maybe 10mm away from) to the corners…

  • Start on one corner – use the paper between the head and the bed…adjust the screw in that corner till it just grips.
  • Move to the next corner, repeat
  • repeat again
  • repeat again

6 – Go back and check each corner and tweak slightly if necessary

7 – Turn printer on and LEVEL THE BED IN SOFTWARE AS NORMAL……

 

Now, if you really want to be pedantic, you should do this whilst everything’s warmed up to your normal working temperatures!

That’s it, the end

 

 

 

 

Calibration – Part 2……Again!

280 x 280mm

https://www.thingiverse.com/thing:2479352/

After figuring out that 20mm, just ain’t good enough to calibrate, I had a nose around on thingverse….

The largest ‘calibration’ thing I found was the above 280 x 280mm square……..Awesome, that’s good enough, close to 300mm too for maximum calibratory goodness…

Continue reading “Calibration – Part 2……Again!”

Nozzles!….what a minefield

51NqYBk5p0L

Well, as i’m thinking ahead for a change and have purchased some glow in the dark filament

I’ve now discovered that the stuff is quite abrasive and I really should be thinking about getting some spare nozzles

A quick search for ‘replacement nozzles’ and….err

Continue reading “Nozzles!….what a minefield”

Thoughts on technical things

STM

Levelling 3D printers almost seems like some form of witchcraft..….Doubly so when you have a small amount of mechanical knowledge and have some electrical PCB tinkering ability

The Wanhao D9 is a Prusa style printer – it has a moving bed and a fixed gantry

A slight difference is that the D9 has Dual Z axis stepper motors – BOTH sides of  the Z axis are driven, which adds another dimension to the levelling whajmacallits.

Continue reading “Thoughts on technical things”

Technical Stuff – Noise

 

Well, having left the printer on overnight to knock out an urgent print for a friend, I’ve discovered that, it’s a little on the noisy side!

Some googling…….

The Wanhao D9 has FOUR fans!  (yep, FOUR)

One 60x60x15mm fan in the power supply and Three 40x40x10

 

Two of these…AAA HZHZ 4010 MS 24V DC 0.10Amp fans

40mmFAN

One on the extruder, right by the number 7, top yellow arrow

This one is the fan that cools the extruder block

Continue reading “Technical Stuff – Noise”

Wanhao Duplicator 9 – D9 – Technical ‘stuff’ – Part Deux, the LCD Part number!

LCD

As you can gather, I get a little sidetracked, this thing’s a 3D printer and, well, I’ve not done a huge amount of 3D printering yet……….Ah well

Lets go back to DWIN.com.cn  

The T5 Processor on the back of the LCD

T5

Continue reading “Wanhao Duplicator 9 – D9 – Technical ‘stuff’ – Part Deux, the LCD Part number!”