sUPER LeD bLInkENAtor 2000 Jun20 Edition

Got me a little tweakin’ time today –

Step 1, Export a PDF from EASYEDA. Print out paper templates, test roughly for fit and alignment
Step 2 – Export DXF from EASYEDA and IMPORT into Fusion360, Tidy up and extrude. Here i’m trying a 1.6mm thick PCB

Step 3 – PRINT. Draft mode is just fine, 2.5 hours later, i’ll have a ‘PCB’!

Have spent a few hours fine tuning alignments – with the new ‘underneath’ mounting of the solderless Blinkenator trial, some of the alignment changes.

The J15 Connector shifts away from the edge about 3/4 mm due to the curvature of the next case, which also needs the larger pillar holes to be moved and increased in size a little.

Step 4 – Printed
Step 5 – Test fit

The print fitted almost perfectly, slight misalignment with J15, I’ll probably make the two locating holes a little larger to allow a little play. The 3D print won’t be the exact same dimensions as the manufactured PCB but it’s close enough to see what tweaks are needed.

And, finally an update on the new next is at Kickstarter!!

Super LED Blinkenator 2000 Stuff –

Sorry for a lack of News of late…….

Have been having a little bit of a creative Block with the Blinkenator. It’s a typical story where ‘something shiny’ has been spotted and has been taking up the small chunks of time I’d normally allocate to this stuff.

I’m awaiting on those Pogo pins to test the next revision…….But, have also seriously re-thought the programminator / tester device…….And, we have what you see above

ROUGH IDEA OF CONNECTIVITY, The programminator sits ‘underneath’ the J15

The Plan.

40 Pin Raspberry Pi connector will allow some ‘playing’ around with the ESP device, and programming of the Arduino. I’ll need to figure out exactly how to write the software to do it- but, there’s dozens of tutorials out there so i’m confident.

Programming could also be done via a standard 6 or 10 pin ICSP device (that can be bought for a few quid off Ebay) directly on the blinkenator itself, or via the 9 pin connector at the bottom – which breaks out to the Programminator.

The Programminator also utilises the J15 connector of the Blinkenator – This should be a great way of testing the new Pogo pins connections as my Specnext J15 is fairly well shot

There’s 2 new holes – 57mm spaced (same as a Raspberry Pi!) which can sit standoffs which match the positioning on the programminator (rasperry pi footprint)

Took quite a while to get this far – now at least you should be able to see the LED’s doing their stuff whilst connected to a Pi and a test board!

June 2021 Revision of the Blinkenator

I’m very close now to getting this new board done as a BETA….next step is to print out, test fit and tweak

In other Interesting news, JLCPCB ‘s NEW version of EasyEDA exports OBJ files! I’ve literally just discovered that you can EXPORT a 3D model of your PCB.

That’s a game changer!

A quick Bodge-up with Microsoft 3D Builder

Why it’s a Game Changer – Simply use Microsoft 3D builder or Tinkercad (or anything really, those two are just superbly easy to use

Assemble your bits – whack ‘print’ and, send to a 3D printer. Or put into your favourite slicer program and do the same – I’ll have a little bit more of a play tomorrow – it’s 11PM now. Now, to use the Resin printer or the Filament one 🙂

Oh, as for the ‘something shiny’ that’s come along…..Checking the logs in Fusion360, I started back on the 8th February. Since then I’ve easily spent 200+ hours editing, tweaking, Learning. I made the first 3D print last week. There will be many more prints till it’s ‘final’ .

There’ll be a few versions of electronics inside, Basic version will likley be some type of Raspberry Pi – Compute Module , A design is well underway. I’m also possibly thinking of dabbling in FPGA, though a 6 layer double sided PCB is a bit daunting, I’m designing one anyway after gaining a big bit of help from someone who’s already familiar with FPGA’s

I’m being vague as I really don’t know where this one’s going. I’ll need to show this publicly, once it’s done and then see what occurs. I’ll need a new, larger resin printer for sure if it takes off though, it uses the entire build volume of my Anycubic Photon Mono printing off the two larger pieces at an angle!